Federal Engineering and Testing, Inc.

Federal Engineering & Testing Inc. was founded in 1989.
We provide Geotechnical, Construction Materials Testing, Inspections and Environmental Services. Our laboratory is accredited by The Florida Department of Transportation (FDOT), The Construction Materials Engineering Council (CMEC) and US Army Corp of Engineers (USACE). Our firm is also certified by Miami-Dade for roof testing.

SPT Borings with Truck Drill Rig, Auger Borings with Truck Drill Rig, Exfiltration / Percolation Test with Truck Drill Rig, SPT Borings with Tripod Equipment, DCP Boring with Hand Equipment, Hand Auger Boring, Undisturbed Sampling of Soil (Shelby Tube/Split Spoon), Static Cone Penetration Tests, Muck Probes, Double Ring Infiltrometer Tests, Monitoring Well Installation, Recovery Well Installation, Environmental Drilling, Rock Coring, GEOTECHNICAL INSPECTIONS, Cast Auger Pile Installation Monitoring, Helical Pile Installation Monitoring, Pin Pile Installation Monitoring, Driven Pile Installation Monitoring, Micro Pile Installation Monitoring, Pile Load Test, Grout Injection Monitoring, Foundation Stabilization Monitoring, Drilled Shaft Inspection, Demucking Inspection, Vibroflotation Inspection, Vibratory Compaction, Seismic Vibration Monitoring, Deep Dynamic Compaction Monitoring, Preliminary Site Reconnaissance, Groundwater Monitoring, Test Pit Excavations and Logging, GEOTECHNICAL ENGINEERING, Geotechnical analysis and reporting, Foundation Analysis & Recommendations, Shallow Foundations, Deep Foundations, Soil Improvement Techniques, Vibroreplacement, Munsel Color Evaluation, Existing Building Structural Settlement Surveys, Dewatering Analysis and Design, Forensic Investigation, Specification Review, Pavement Analysis and Design, Soil Cement and Lime Stabilization, Geosynthetic Reinforcement Design, Aerial Photograph Interpretation, Geological Studies, Soil and Materials Specifications, Slope Stability Analysis, Steepened Slope Design, Retention Systems Design, Site Development Feasibility Studies, Casting Concrete Cylinders, Casting Concrete Beams, Casting Concrete Cubes, Casting Concrete Grout Prisms, Compressive Strength Test, Drilled Cores, Concrete Thickness Verification, Concrete Flexural Strength, Unit Weight & Density, Slump of Fresh Concrete, Sampling Fresh Concrete, Concrete Air Content, Curing Concrete Specimens, Capping Concrete Specimens, Rebound Hammer Test, Windsor Probe, Grout Flow Test, Temperature of Fresh Concrete, AGGREGATE TESTING, Organic Impurities, Fine Aggregate Passing #200 Wash, Coarse Aggregate Passing #200 Wash, Fine Aggregate Gradation, Coarse Aggregate Gradation, Specific Gravity of Fine Aggregate, Specific Gravity of Coarse Aggregate, Clay Lumps & Friable Particles, Moisture Content Test, Sample Reduction, L.A. Abrasion, ASPHALT TESTING, Asphalt Thickness Verification, Asphalt Cores, Nuclear Backscatter Density, Asphalt Content by Ignition, Extraction & Gradation, Marshall Resistance, Specific Gravity, Asphalt Paving Monitoring, Spread Rate Calculation, SOIL TESTING, Nuclear Density Test, Speedy Moisture Test, Soil Sample Collection, Dry Preparation, Wet Preparation, Standard Proctor Test, Modified Proctor Test, Particle Size Analysis (Sieve), Specific Gravity, Finer than #200 Wash, California Bearing Ratio (CBR), Limerock Bearing Ratio (LBR), Florida Bearing Value (FBV), Moisture Content, Classification of Soils, Description of Soils, Atterberg Limits, Organic Loss by Ignition, pH Content, Unit Weight & Yield, , Shingle to Tile Inspections, Roof Drainage Calculations, Standing Seam Inspections, Fastener Spacing Calculations, Retrofit & Insurance Mitigations, Pre & Post Hurricane Inspections, Lightweight Concrete Inspections, Cap Sheet Installation Inspections, Wind Load & Skylight Calculations, Tin Cap & Base Sheet Inspections, Roof Assessments & or Evaluations, Roof Sheathing Re-Nail Inspections, TAS-105 - Field Withdrawal Test, TAS-124 - Bonded or Bell Chamber, TAS-126 - Nuclear Moisture Survey.